If your residential or commercial property has a septic system, keeping it in operating condition is extremely essential. A clogged tank, broken pipeline, or blocked sewer pipe can result in a cascade of problems. If you notice your pipes are draining slowly or backing up, there’s a fat chance the lines are clogged, and if not fixed immediately, may lead to costly repairs and potential environmental hazards.
In this blog post, we’ll address some repair strategies for tackling common septic troubles in Bremerton, Port Orchard, Shelton, and nearby areas.
How to Unclog a Septic System?
Leading septic tank pumping contractors in Shelton reveal that the steps to unclogging a septic system include
1. Prepare Your Tools and Protective Equipment
Before unclogging a septic line, prepare everything you may need to clean up afterward. Top septic experts in Bremerton insist on putting on rubber gloves, a gas mask, safety goggles, and wearing durable clothing that covers your legs and arms. Then, you can mix five parts of water and bleach in a gallon bucket to create a sanitizing solution.
2. Access the Septic Line
Find the septic tank cover in your yard that is closest to your house. If you don’t know where this is, you may need to refer to your home’s as-built drawings. If the lid isn’t easy to remove on your own, use the pry bar to lift one side gently. Then, pick up the lid and set it somewhere nearby. Be careful not to lean too far over the side of the opening, and look for the end of a pipe that runs from the septic tank to your home.
3. Clear Visible Clogs
Using the wooden pole or steel rod, gently but firmly push the scum layer to the side of the pipe or tank. If you notice water refilling the reservoir, this is your sign that you’re clearing the clog. Continue to push the pole or rod into the pipe.
If you probe the pipe and don’t notice any change in water flow, the clog may be harder to access. It may be possible to rent a mechanical auger to reach farther into the line, but this could potentially damage the line if you aren’t experienced.
4. Clean and Sanitize
Immediately after the line is clear, submerge all the materials you used into the bleach solution for at least five minutes. Then, dump the bleach solution directly into the septic tank and replace the tank lid. Leading septic tank professionals in Port Orchard suggest washing your clothes in a sanitizing cycle in the washing machine and taking a long shower.
5. Get Your Septic Tank Professionally Pumped
If the blockage was caused by the septic tank being full or close to capacity, you must schedule an appointment with a credible septic pumping professional like Danos Septic to pump the tank as soon as possible. Our technician will arrive promptly equipped with specialized tools and equipment to safely and efficiently pump out the contents of your septic tank. They’ll also inspect the area for leaks or other issues.
How do you Fix a Crack in a Sewer Pipe?
Top septic pumping contractors in Bremerton reveal that fixing a crack in a sewer pipe involves several steps.
- First, visually inspect the crack or use specialized equipment like a camera to locate the crack.
- Once found, clean the area around the crack thoroughly.
- Then, depending on the severity of the crack, you may patch it using epoxy or a repair sleeve for minor cracks.
- If the pipe has larger cracks or damage, you may need to replace the affected section. Proper sealing and support are essential to prevent leaks and further damage.
- Finally, a thorough inspection needs to be conducted to confirm the effectiveness of the repair and prevent future issues. If unsure, it’s best to consult a professional plumber, especially from a credible septic company like Danos Septic, for assistance.
How do you Clear a Septic Line?
Leading septic tank pumping specialists in Shelton reveal that the two basic steps to clearing a septic line include,
- First, locate the access point to the septic system.
- Next, use a plumbing snake or an auger to break through any clogs or blockages in the line. If the clog persists, try a sewer jetter to blast away debris using high-pressure water.
In more severe cases, professional assistance may be necessary. A qualified plumber or a credible septic tank service like Danoz Septic must assess and effectively clear the blockage.
Top septic experts in Port Orchard also caution that to avoid future clogs, it’s important to keep up with regular maintenance tasks, refrain from flushing non-biodegradable items, and use products that are safe for septic systems.
How do you Fix a Cracked Water Pipe?
Top septic system contractors in Bremerton suggest the following steps to fix a cracked water pipe efficiently:
- To fix a cracked water pipe, turn off the water supply to prevent further damage, then drain any remaining water from the pipes.
- Next, locate the crack and clean the area around it. Depending on the size of the crack, you can temporarily seal it with epoxy putty or a pipe repair clamp.
- For a more permanent solution, you may need to cut out the damaged section and replace it with a new piece of pipe.
- Finally, turn the water supply back on and check for any leaks to ensure the repair was successful.
Lastly, if you’re unsure or unable to fix it, feel free to contact Danos Septic for assistance.
Final Words
If you’re facing any kind of septic-related emergency, contact the skilled professionals at Danos Septic. With more than 30 years of experience in the industry, we specialize in septic systems and offer services such as grease trap, septic tank pumping, inspections and repairs, septic locating, drain field rejuvenation, and installations for commercial and residential customers in Shelton, Port Orchard, Bremerton, and surrounding areas.
Call today, and a Danos team member will answer your call 24 hours a day, seven days a week, giving you a competitive price and the septic solution that is right for you!
Contact us at (360)205-1924 to schedule an appointment with our team today.
